How to Build a “Floating” Floor

Solid construction materials and authorized Auralex products are highly recommended. Always use appropriate safety equipment like gloves and safety glasses.

 

Project Overview

The floor is the single most critical part of any sound-isolated or "floated" room. A floated room features greatly improved transmission loss (isolation) and low frequency definition. A tight, floated room will always sound better!

Estimated Material Cost: $8/sq ft
Time: 2-3 Days

CrossSection.png

 

Guides Referenced in this Project

Auralex Products Used in this Project

Construction Materials Used in this Project

  • Wood or Metal Studs and Joists
  • Plywood
  • Particleboard
  • Mechanical Fasteners & Adhesives 

 

1. Frame Construction and Placement 

Framing-Spacing-1.png

Construct the frame for your floating floor from 2’x4’ or 2x’6’ Wood Studs, spaced 2’ apart with stringers every 4’ (to match the dimensions of the Mineral Fiber insulation). To prevent wood warp and add stability, alternate stringer placement.

 

Framing-Spacing-2.png

The floor frame will determine the size of your finished enclosure, so design your frame slightly smaller than the existing space. Once built, position your frame to maintain a 2” minimum gap around all sides and any existing structure. 

 

2. Installing U-Boat™ Floor Floaters

Made of a specially-formulated rubber compound, U-Boat™ Floor Floaters are our proprietary U-shaped channels used to support framing members and float (isolate and decouple) them from the surrounding structure. With the help of U-Boats, a floated room features greatly improved transmission loss (isolation) and low frequency definition (translated: a tight, floated room will always sound better!).

 

Framing-1.png

To prepare for U-Boat installation, lift your frame on risers using spare stud scraps.

 

Framing-Spacing.png

With the frame on risers, use a brad nail or staple to secure U-Boats every 1’ on all exterior members, and every 18” on all interior members. 

 

U-BoatsClose.png

 

U-Boats.png

With all U-Boats placed, remove the frame risers and drop the frame into place.

 

U-Boats3.png

After removing the risers your new floor frame should rest cleanly on the installed U-Boats, ½” above the existing floor.

 

 

 

3. Installing Mineral Fiber Insulation

Mineral Fiber Insulation is the workhorse of our isolation materials. It is a insulation panel which provides acoustic isolation as well as typical insulation properties.

 

MG-1.png

Place Mineral Fiber Insulation between each frame member, making necessary cuts to create a snug fit around all sides.

 

MF-1.png

 

MF-Spacing.png

Allow the Mineral Fiber Insulation to float between the frame members by resting on the U-Boats. Additionally, there should be a small gap between the insulation and the top of the studs, where your sub floor will rest.

 

 

4. Sub-Floor - First Layer

SubFloor-1.png

Install your first layer of subfloor, using StopGap™ Sealant between each seam. Take note of the location and direction of the seams in your subfloor material.

 

SubFloor.png

 

5. SheetBlok™ Sound Barrier Installation

SheetBlok.png

Install a layer of SheetBlok™ Sound Barrier on top of your first layer of subfloor, laying the sheets in a different direction than the subfloor - minimizing air flow, and thus sound transfer. As a further counter-measure, fill all seams in the SheetBlok with StopGap™ Sealant.

What’s the best method to install SheetBlok?

 

6. Subfloor - Final Layer

SubFloor-2a.png

Install your second layer of subfloor again in an alternating pattern, not allowing seams to overlap. Once the rest of the room build is complete and we’re ready to lay our finished flooring, we will complete this subfloor with a final application of StopGap™ Sealant between the seams.

 

Side.png

When complete, the SheetBlok can be viewed between the two layers of subfloor, with offset seams.

Was this article helpful?
2 out of 2 found this helpful

Comments

0 comments

Please sign in to leave a comment.